Plastic

Plastic is the general common term for a wide range of synthetic or semi-synthetic organic amorphous solid materials used in the manufacture of industrial products. Plastics are typically polymers of high molecular mass, and may contain other substances to improve performance and/or reduce costs. Monomers of Plastic are either natural or synthetic organic compounds.

The word is derived from the Greek πλαστικός (plastikos) meaning fit for molding, and πλαστός (plastos) meaning molded. It refers to their malleability, or plasticity during manufacture, that allows them to be cast, pressed, or extruded into a variety of shapes—such as films, fibers, plates, tubes, bottles, boxes, and much more.

Household items made of various kinds of plastic.

The common word plastic should not be confused with the technical adjective plastic, which is applied to any material which undergoes a permanent change of shape (plastic deformation) when strained beyond a certain point. Aluminum, for instance, is plastic in this sense, but not a plastic in the common sense; in contrast, in their finished forms, some plastics will break before deforming and therefore are not plastic in the technical sense.

There are two types of plastics: thermoplastics and thermosetting polymers. Thermoplastics will soften and melt if enough heat is applied; examples are polyethylene, polystyrene, polyvinyl chloride and polytetrafluoroethylene (PTFE) Thermosets can melt and take shape once; after they have solidified, they stay solid.

Overview

Plastics can be classified by chemical structure, namely the molecular units that make up the polymer's backbone and side chains. Some important groups in these classifications are the acrylics, polyesters, silicones, polyurethanes, and halogenated plastics. Plastics can also be classified by the chemical process used in their synthesis, such as condensation, polyaddition, and cross-linking.

Other classifications are based on qualities that are relevant for manufacturing or product design. Examples of such classes are the thermoplastic and thermoset, elastomer, structural, biodegradable, and electrically conductive. Plastics can also be classified by various physical properties, such as density, tensile strength, glass transition temperature, and resistance to various chemical products.

Due to their relatively low cost, ease of manufacture, versatility, and imperviousness to water, plastics are used in an enormous and expanding range of products, from paper clips to spaceships. They have already displaced many traditional materials, such as wood; stone; horn and bone; leather; paper; metal; glass; and ceramic, in most of their former uses.

The use of plastics is constrained chiefly by their organic chemistry, which seriously limits their hardness, density, and their ability to resist heat, organic solvents, oxidation, and ionizing radiation. In particular, most plastics will melt or decompose when heated to a few hundred degrees celsius. While plastics can be made electrically conductive to some extent, they are still no match for metals like copper or aluminum.^{[citation needed]} Plastics are still too expensive to replace wood, concrete and ceramic in bulky items like ordinary buildings, bridges, dams, pavement, and railroad ties

History

The first human-made plastic was invented by Alexander Parkes in 1855 ; he called this plastic Parkesine (later called celluloid). It was unveiled at the 1862 Great International Exhibition in London. The development of plastics has come from the use of natural plastic materials (e.g., chewing gum, shellac) to the use of chemically modified natural materials (e.g., rubber, nitrocellulose, collagen, galalite) and finally to completely synthetic molecules (e.g., bakelite, epoxy, polyvinyl chloride, polyethylene).

Chemical structure

Common thermoplastics range from 20,000 to 500,000 in molecular mass, while thermosets are assumed to have infinite molecular weight. These chains are made up of many repeating molecular units, known as repeat units, derived from monomers; each polymer chain will have several thousand repeating units. The vast majority of plastics are composed of polymers of carbon and hydrogen alone or with oxygen, nitrogen, chlorine or sulfur in the backbone. (Some of commercial interests are silicon based.) The backbone is that part of the chain on the main "path" linking a large number of repeat units together. To customize the properties of a plastic, different molecular groups "hang" from the backbone (usually they are "hung" as part of the monomers before linking monomers together to form the polymer chain). This fine tuning of the properties of the polymer by repeating unit's molecular structure has allowed plastics to become such an indispensable part of twenty first-century world.

Some plastics are partially crystalline and partially amorphous in molecular structure, giving them both a melting point (the temperature at which the attractive intermolecular forces are overcome) and one or more glass transitions (temperatures above which the extent of localized molecular flexibility is substantially increased). The so-called semi-crystalline plastics include polyethylene, polypropylene, poly (vinyl chloride), polyamides (nylons), polyesters and some polyurethanes. Many plastics are completely amorphous, such as polystyrene and its copolymers, poly (methyl methacrylate), and all thermosets.

Nylon

The real star of the plastics industry in the 1930s was polyamide (PA), far better known by its trade name nylon. Nylon was the first purely synthetic fiber, introduced by DuPont Corporation at the 1939 World's Fair in New York City.

In 1927, DuPont had begun a secret development project designated Fiber66, under the direction of Harvard chemist Wallace Carothers and chemistry department director Elmer Keiser Bolton. Carothers had been hired to perform pure research, and he worked to understand the new materials' molecular structure and physical properties. He took some of the first steps in the molecular design of the materials.

His work led to the discovery of synthetic nylon fiber, which was very strong but also very flexible. The first application was for bristles for toothbrushes. However, Du Pont's real target was silk, particularly silk stockings. Carothers and his team synthesized a number of different polyamides including polyamide 6.6 and 4.6, as well as polyesters.^[9]

General condensation polymerization reaction for nylon

It took DuPont twelve years and US$27 million to refine nylon, and to synthesize and develop the industrial processes for bulk manufacture. With such a major investment, it was no surprise that Du Pont spared little expense to promote nylon after its introduction, creating a public sensation, or "nylon mania".

Nylon mania came to an abrupt stop at the end of 1941 when the USA entered World War II. The production capacity that had been built up to produce nylon stockings, or just nylons, for American women was taken over to manufacture vast numbers of parachutes for fliers and paratroopers. After the war ended, DuPont went back to selling nylon to the public, engaging in another promotional campaign in 1946 that resulted in an even bigger craze, triggering the so called nylon riots.

Subsequently polyamides 6, 10, 11, and 12 have been developed based on monomers which are ring compounds; e.g. caprolactam. Nylon 66 is a material manufactured by condensation polymerization.

Nylons still remain important plastics, and not just for use in fabrics. In its bulk form it is very wear resistant, particularly if oil-impregnated, and so is used to build gears, plain bearings, and because of good heat-resistance, increasingly for under-the-hood applications in cars, and other mechanical parts.

Synthetic rubber

The first fully synthetic rubber was synthesized by Lebedev in 1910. In World War II, supply blockades of natural rubber from South East Asia caused a boom in development of synthetic rubber, notably Styrene-butadiene rubber (a.k.a. Government Rubber-Styrene). In 1941, annual production of synthetic rubber in the U.S. was only 231 tons which increased to 840 000 tons in 1945. In the space race and nuclear arms race, Caltech researchers experimented with using synthetic rubbers for solid fuel for rockets. Ultimately, all large military rockets and missiles would use synthetic rubber based solid fuels, and they would also play a significant part in the civilian space effort.

Cellulose-based plastics

In 1855, an Englishman from Birmingham named Alexander Parkes developed a synthetic replacement for ivory which he marketed under the trade name Parkesine, and which won a bronze medal at the 1862 World's fair in London. Parkesine was made from cellulose (the major component of plant cell walls) treated with nitric acid and a solvent. The output of the process (commonly known as cellulose nitrate or pyroxilin) could be dissolved in alcohol and hardened into a transparent and elastic material that could be molded when heated. By incorporating pigments into the product, it could be made to resemble ivory.

Bois Durci is a plastic molding material based on cellulose. It was patented in Paris by Lepage in 1855. It is made from finely ground wood flour mixed with a binder, either egg or blood albumen, or gelatine. The wood is probably either ebony or rose wood, which gives a black or brown resin. The mixture is dried and ground into a fine powder. The powder is placed in a steel mold and compressed in a powerful hydraulic press whilst being heated by steam. The final product has a highly polished finish imparted by the surface of the steel mold.

Bakelite

The first plastic based on a synthetic polymer was made from phenol and formaldehyde, with the first viable and cheap synthesis methods invented in 1909 by Leo Hendrik Baekeland, a Belgian-born American living in New York state. Baekeland was searching for an insulating shellac to coat wires in electric motors and generators. He found that mixtures of phenol (C₆H₅OH) and formaldehyde (HCOH) formed a sticky mass when mixed together and heated, and the mass became extremely hard if allowed to cool. He continued his investigations and found that the material could be mixed with wood flour, asbestos, or slate dust to create "composite" materials with different properties. Most of these compositions were strong and fire resistant. The only problem was that the material tended to foam during synthesis, and the resulting product was of unacceptable quality.

Baekeland built pressure vessels to force out the bubbles and provide a smooth, uniform product. He publicly announced his discovery in 1912, naming it bakelite. It was originally used for electrical and mechanical parts, finally coming into widespread use in consumer goods in the 1920s. When the Bakelite patent expired in 1930, the Catalin Corporation acquired the patent and began manufacturing Catalin plastic using a different process that allowed a wider range of coloring.

Bakelite was the first true plastic. Originally called plasdick, but the name was unappealing. It was a purely synthetic material, not based on any material or even molecule found in nature. It was also the first thermosetting plastic. Conventional thermoplastics can be molded and then melted again, but thermoset plastics form bonds between polymers strands when cured, creating a tangled matrix that cannot be undone without destroying the plastic. Thermoset plastics are tough and temperature resistant.

Bakelite was cheap, strong, and durable. It was molded into thousands of forms, such as cases for radios, telephones and clocks, and billiard balls. The U.S. government even considered making one-cent coins out of it when World War II caused a copper shortage.^{[citation needed]}

Phenol-based ("Phenolic") plastics have been largely replaced by cheaper and less brittle plastics, but they are still used in applications requiring their insulating and heat-resistant properties. For example, some electronic circuit boards are made of sheets of paper or cloth impregnated with phenolic resin.

Phenolic sheets, rods and tubes are produced in a wide variety of grades under various brand names. The most common grades of industrial phenolic are Canvas, Linen and Paper.